Home > Parts and Hardware > Replacement Parts by Printer > MendelMax 3 Parts
Sort By:
Page of 1
Xtreme Dual V Wheel - Replacement wheel only

Replacement wheel for the MendelMax 3 Y Axis. This is the polycarbonate wheel only and does not include the bearings or any hardware.

Our Price: $3.95
Xtreme Standard V Wheel - Replacement wheel only

Replacement wheel for the MendelMax 3 X & Z Axis. This is the polycarbonate wheel only and does not include the bearings or any hardware.

Our Price: $3.95
Borosilicate Glass, 250 mm x 320 mm x 3.3 mm for the MendelMax 1.5, 2, 3 & MTW Create

Borosilicate glass is the industry-standard glass for heat resistant applications. Standard for laboratory glassware and high-end kitchen utensils, this is also the glass that glass-specialists recommend for 3D printer purposes. Our glass is a hefty 3.3 mm thick, and it also has softened edges to prevent accidental abrasions. Sized at 250 mm x 320 mm, this fits our Bed Heater, 240 mm x 310 mm Kapton.

Technical Specifications

  • Material: borosilicate glass
  • Dimensions: 250 mm x 320 mm x 3.3 mm
  • Edges: softened

Our Price: $26.95
IR Sensor for Auto Bed Leveling

IR Sensor for Auto Bed Leveling

Note:

For the IR ABL system to work properly you cannot use a shiny surface. The heatspreader under the glass needs to be painted flat black for proper operation.

Our Price: $39.00
BLTouch Auto Bed Levelling Touch Sensor

The Genuine BLTouch Automatic Bed Leveling Touch Sensor from ANTCLabs is the easiest and most reliable method we have found to automatically level your 3d Printer bed.

Please note: The BLTouch is not compatible with the MiniRAMBo Controller used on the MIniMax printer. To use it with the MendelMax 2, MendelMax 3 or MTW Create, be sure to add the optional wire harness to save having to create your own.


Main functions and controls of BLTouch are same as usual auto bed leveling sensor, consists of RC servo and micro switch.

Thus, BLTouch can be applied on almost every board.

BLTouch fulfilled simple structure and high precision by using progressively designed solenoid and hall sensor, and aimed user convenience and enjoyable printing by adding many smart functions, self-test, alarm, alarm release, test mode for M119.

Simple

  • BLTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because BLTouch works as usual auto bed leveling sensor.

Smart

  • Self-test : The push pin is operated three times to test when the power is on
  • Alarm : The LED light blinks if a problem found on a self-test or on an operation

High-precision

  • BLTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise. (refer to attached video)

※ The data above can be varied by assembling shape and other environments.

※ In this video, the result of Standard Deviation was around 0.001mm.
But at the other low quality 3D printer, we just get the value as 0.001~0.05mm. (It was the same BLTouch.) Actually, around 0.05 is also not much problem at FDM type 3D printers.

Unlike 3D printer firmware, There isn't any delay at BLTouch, because it uses interrupt inside.
So, BLTouch outputs pulse signal as soon as a hall sensor senses a magnet.
The things that affect to Standard Deviation is,
1. Probing speed of 3D printer
2. Assembled quality of 3D printer
3. Destroyed(Damaged) push-pin

If you choose BLTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience.

BLTouch consists of Atmel ATtiny13A, solenoid, and a push pin.

Innovative Solenoid : Ultra Power Saving

On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device.

Low power consumption even further drops joule heating, preventing from heat problem.

Hall Sensor : Free Bed Selection

BLTouch does not uses either optical, nor proximity(inductive/capacitive) sensor.

BLTouch is controlled by hall effect, providing high precision. Thus the bed material can be selected freely.

Optimized structure : Larger Build Size

BLTouch is a small, and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor.

BLTouch uses existing RC Servo motor signal intactly, so just plug BLTouch on the same pins after removing servo motor.

Our Price: $44.95
MM3 Machined Bed Upgrade

Note: This carriage uses the same V Wheels as your current Y carriage. It does not convert the MM3 to use the Create linear rails.

Our Price: $59.00